๑۩۞۩๑ Boot Repair Specials ۞ Riff Jtag ۞ Medusa Jtag ۞ Gpg Jtag ۞ Official Reseller ۞ All@Best Prices.For Further Details-Pls Call: 9942434855 ๑۩۞۩๑

RIFF JTAG - Weekend Updates

Written by Administrator | 04 October 2011

<<< RIFF BOX-JTAG REVOLUTION >>>

Rocker Team Flashing Interface

we are the authorised Reseller

CONTACT US FOR BEST PRICE

RIFF JTAG Features

RIFF JTAG firmware supports following features at the moment:

ARM7/ARM9/ARM11 PXA3xx, PXA270, Cortex-A8, OMAP850, cores support;
Multiple devices on JTAG chain are supported, thus TAP number selection is available;
Any custom voltage level selection from range ~1.4V to 3.3V
TCK/Adaptive clocking selection
Halt core (NRST is not changed)
Reset core (NRST is applied before halt)
Direct Read memory (by 8/16/32-bit bytes/half-words/words)
Direct Write memory (by 8/16/32-bit bytes/half-words/words)
Access to the control registers of ARM core (coprocessor 15)
Program code breakpoints
Run core
Custom scripting and DCC loader support (trace32 compatible)
Custom GDB Server Available
I/O pins detection !Unique feature offered only by RIFF JTAG

This is result of six months hard work. And we just started -;)
Stay tuned for more !

This is the list of available RIFF JTAG Resurrectors DLL-s , which You can use for one click dead boot repair.
List will be updated with new releases, and this is only small part of models we will add.

GPS Devices:

Daewoo DPN3500 – Boot repair

Mobile phones and communicators :

DELL XCD28 Boot Repair/Unbrick
DELL Streak (DELL Mini 5) Boot Repair/Unbrick

Eten X800 Boot repair/Unbrick

HTC Desire Boot repair/Unbrick, Unlock, IMEI Change/repair CID Change
HTC Diamond Boot repair/Unbrick, Unlock, IMEI Change/repair
HTC Dream – Google G1 Boot repair/Unbrick, Unlock, IMEI Change/repair, Activation bypass
HTC HD2 LEO Boot repair/Unbrick, Unlock, IMEI Change/repair CID Change
HTC Herald Boot repair/Unbrick
HTC Touch P3452 – HTC Elfin – bootloader restore
HTC Magic32A Boot repair/Unbrick, Unlock, IMEI Change/repair
HTC Magic32B Boot repair/Unbrick, Unlock, IMEI Change/repair
HTC Nexus Boot repair/Unbrick, Unlock, IMEI Change/repair
HTC RhodiumW Boot repair/Unbrick, Unlock, IMEI Change/repair
HTC Rhodium Touch Pro2 Boot repair/Unbrick, Unlock, IMEI Change/repair, CID Change
HTC Topaz Boot repair/Unbrick, Unlock, IMEI Change/repair
HTC Touch HD Boot repair/Unbrick, Unlock, IMEI Change/repair, CID Change
HTC Touch2 Mega Boot repair/Unbrick, Unlock, IMEI Change/repair, CID Change
HTC Imagio/Whitestone repair/Unbrick, Unlock, IMEI Change/repair, CID Change
HTC Snap – Maple 120, Maple 100repair/Unbrick, Unlock, IMEI Change/repair, CID Change
HTC Dash repair/Unbrick, Unlock, IMEI Change/repair, CID Change
HTC Tattoo Click 100 Boot repair/Unbrick, Unlock, IMEI Change/repair, CID Change
HTC Niki (HTC Touch Dual) Boot repair/Unbrick, Unlock, IMEI Change/repair, CID Change
HTC Kovalsky Boot repair/Unbrick, Unlock, IMEI Change/repair, CID Change
HTC Jade (HTC Touch 3G T3232) Unbrick/Boot Repair, Unlock, IMEI Change/repair, CID Change
HTC Legend Unbrick/Boot Repair, Unlock, IMEI Change/repair, CID Change
HTC Wildfire Unbrick/Boot Repair, Unlock, IMEI Change/repair, CID Change
HTC Hero Unbrick/Boot Repair, Unlock, IMEI Change/Repair, CID Change
HTC Wings (HTC S730 US) Boot Repair, IMEI Change, CID Change

SE Xperia X1 Boot repair/Unbrick, Unlock, IMEI Change/repair, CID Change

Samsung B7330 Boot Repair/Unbrick
Samsung C5510 Boot Repair/Unbrick
Samsung F480 Boot Repair/Unbrick
Samsung F500 modem Boot Repair/Unbrick
Samsung G810 modem Boot Repair/Unbrick
Samsung G810 PDA Boot Repair/Unbrick
Samsung i450 modem Boot Repair/Unbrick
Samsung i450 PDA Boot Repair/Unbrick
Samsung i550 modem Boot Repair/Unbrick
Samsung i550 PDA Boot Repair/Unbrick
Samsung i560 PDA Boot Repair/Unbrick
Samsung i568 PDA Boot Repair/Unbrick
Samsung i560 modem Boot Repair/Unbrick
Samsung i568 modem Boot Repair/Unbrick
Samsung i5500 Galaxy Boot Repair/Unbrick
Samsung I5700 Boot Repair/Unbrick
Samsung i5800 Boot Repair/Unbrick
Samsung i710 Boot Repair/Unbrick
Samsung i718 Boot Repair/Unbrick
Samsung i740 PDA Boot Repair/Unbrick
Samsung i740 Modem Boot Repair/Unbrick
Samsung I7500 Boot Repair/Unbrick
Samsung i780 modem Boot Repair/Unbrick
Samsung i780 PDA Boot Repair/Unbrick
Samsung i897 Captivate Boot Repair/Unbrick
Samsung I8000 Boot Repair/Unbrick
Samsung i8320 modem Boot Repair/Unbrick
Samsung i8320 PDA Boot Repair/Unbrick
Samsung i8510 modem Boot Repair/Unbrick
Samsung i8510 PDA Boot Repair/Unbrick
Samsung i8910 modem Boot Repair/Unbrick
Samsung i8910 PDA Boot Repair/Unbrick
Samsung I9000 Boot Repair/Unbrick
Samsung i900 modem Boot Repair/Unbrick
Samsung i900 PDA Boot Repair/Unbrick
Samsung i908E modem Boot Repair/Unbrick
Samsung M7500 Boot Repair/Unbrick
Samsung M7600 Boot Repair/Unbrick
Samsung M8910 Boot Repair/Unbrick
Samsung S3310 Boot Repair/Unbrick
Samsung S3370 Boot Repair/Unbrick
Samsung S5230 Boot Repair/Unbrick
Samsung S5510 Boot Repair/Unbrick
Samsung S5560 Boot Repair/Unbrick
Samsung S5600 Boot Repair/Unbrick
Samsung S7070 Boot Repair/Unbrick
Samsung S7350 Boot Repair/Unbrick
Samsung S7350i Boot Repair/Unbrick
Samsung S8000 Boot Repair/Unbrick
Samsung S8300 Boot Repair/Unbrick
Samsung S8500 Boot Repair/Unbrick
Samsung T919 Boot Repair/Unbrick
Samsung T669 Boot Repair/Unbrick
Samsung T959 Boot Repair/Unbrick
Samsung U700 Boot Repair/Unbrick
Samsung U800 Boot Repair/Unbrick
Samsung U900V Boot Repair/Unbrick
Samsung Z240 Boot Repair/Unbrick
Samsung Z540 Boot Repair/Unbrick
Toshiba G810 Boot Repair/Unbrick
Toshiba G910 Boot Repair/Unbrick
Toshiba TG01 Boot Repair/Unbrick, EFS rebuild, Unlock (IMEI will be changed)

ZTE RACER Boot Repair/Unbrick

CDMA Mobile Phones:

Huawei C2806M Repair, Read/Write NOR flash,
Huawei C2901M Repair, Read/Write NOR flash
Huawei C8500 Android Boot Repair/Unbrick, Read Write NAND Flash

Samsung Omnia i910 Repair/Unbrick, Read/Write NAND Flash
Samsung A900 Blade Repair/Unbrick, Read/Write NAND Flash

LG RD3000 Repair, Read/Write NOR flash
LG RD3100 Repair, Read/Write NOR flash
LG RD3500 Repair, Read/Write NOR flash
LG RD3510 Repair, Read/Write NOR flash
LG RD3540 Repair, Read/Write NOR flash
LG RD3610 Repair, Read/Write NOR flash
LG RD6100 Repair, Read/Write NOR flash

ZTE-C N600 Repair, Read/Write NAND flash
ZTE S100 Repair, Read/Write NAND flash
HAIER C2076 Repair, Read/Write NAND flash

Broadband Modems:

ZTE MF100 Boot Repair/Unbrick
ZTE MF112 Boot Repair/Unbrick
ZTE MF622 Boot Repair/Unbrick
ZTE MF626 Boot Repair/Unbrick
ZTE MF628 Boot Repair/Unbrick
ZTE MF170 Boot Repair/Unbrick
ZTE MF180 Boot Repair/Unbrick

Huawei E1550 Boot Repair/Unbrick
Huawei E17X Boot Repair/Unbrick
Huawei E220 Boot Repair/Unbrick
Huawei E585 Boot Repair/Unbrick
Huawei E169 Boot Repair/Unbrick
Huawei E585 Boot Repair/Unbrick
Huawei E160 Boot Repair/Unbrick
Huawei E160G Boot Repair/Unbrick

Tablets :

Samsung Galaxy TAB (Samsung P1000) Unbrick, Repair, Read/Write NAND Flash memory

UPDATES

RIFF JTAG - Weekend Updates

18.05.2012 RIFF JTAG – Weekend updates:

Whats new:

Samsung B7320 unbrick/boot repair support added
HTC Sensation 4G (PG581000) Unbrick, Unlock, S-Off, SuperCID support added
HTC Sensation (PG581300/PG583101) Unlock support added
HTC Evo 3D Unlock support added

Bug Fix updates:

HTC Desire HD Support for new board revisions with hboot 2.xx (No Network problem)
HTC Wildfire S Proximity sensor fix

RIFF Torrent tracker:

RiffBox Setup 18.05.2012 v1

Please click “Check for updates” button in RIFF JTAG Manager to download new files.

RIFF JTAG – Samsung SPH-D710 Galaxy S2 Epic Touch 4G (Samsung Within) Unbrick – dead boot repair supported

11.05.2012 RIFF JTAG – Samsung SPH-D710 Galaxy S2 Epic Touch 4G (Samsung Within) Unbrick – dead boot repair supported

Repairing bricked Samsung SPH-D710 Galaxy S2 Epic Touch 4G is easy with RIFF Box. Samsung SPH-D710 is based on the S5PV310 (Exynos 4210) Processor (Cortex-A9 Dual-Core). JTAG pads are very small; professional experience in soldering is required to connect wires to the JTAG interface.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.

To resurrect Samsung SPH-D710:

Solder JTAG cable to Samsung SPH-D710 JTAG pads;
Connect USB cable to phone and PC;
Insert battery;
Make sure Samsung SPH-D710 is selected in the list of models;
Make sure a fixed TCK frequency is selected;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

Disconnect PC cable;
Insert battery;
Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

RIFF JTAG – Samsung SGH-T679 Exhibit II 4G (Samsung Ancora) Unbrick – Dead Boot repair supported

04.05.2012 RIFF JTAG – Samsung SGH-T679 Exhibit II 4G (Samsung Ancora) Unbrick – Dead Boot repair supported

Repairing bricked Samsung T679 is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Please note, MSM8255T is multi-core chipset – it has ARM11 and Qualcomm Scorpion cores. During power on sequence only ARM11 core is visible on the JTAG chain. If boots are not completely damaged and it comes up to initializing of the Scorpion core then Scorpion core appears on the JTAG chain too. This will shift ARM11 from TAP0 into TAP1 position on the chain, while current resurrector has the ARM11 core hardcoded at TAP0 position. Thus make sure to establish JTAG connection in the time range while Scorpion core is not visible yet.

To resurrect Samsung T679:

Solder JTAG cable to Samsung T679 JTAG pads;
Make sure Samsung T679 is selected in the list of models;
Insert battery and connect USB Data cable;
If you use only battery, press Power On key;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

Disconnect PC cable;
Insert battery;
Hold ‘Volume Down’ key and press ‘Power ON’ button.

samsung_sgh-t679_exhibit_ii_4g

RIFF JTAG-RIFF JTAG Manager v1.43 released

RIFF Box JTAG Manager software setup

This will install following files to Your computer:

JTAG Manager software v1.43
RIFF Box Firmware v1.32
RIFF Box control port driver
RIFF Box update port driver
RIFF DCC USBLoader driver
QUALCOMM QHUSB_DLOAD driver

After You execute setup, it will install all files to desired destination, and launch drivers installer script.
Take note, If You’re using Windows XP, You’ll have to provide drivers location to Hardware Installation Wizard after connecting devices for first time .

RIFF JTAG – HTC via USB more phones supported

27.04.2012 RIFF JTAG – HTC via USB more phones supported

HTC Thunderbolt USB support added
HTC Sensation XL USB support added
HTC Inspire USB support added
HTC Incredible S USB support added
HTC Incredible 2 USB support added

These new updates will allow You to use USB cable to perform any operation on listed models. Remember that this work if Your phone is enumerated on USB port as QHUSB_Dload or Qualcomm HS-USB QDLoader device.
In case phone is not enumerated, You might need to use test point method first.

Please visit RIFF FAQ section to see how to install drivers, and how to find eMMC Vdd test points:

If You need to repair phone after replacing eMMC chip, these are the steps:

Launch eMMC MBR/EBR partitioning tool
Open desired partitioning file
Click “Load Image from file”
Click “Repartition eMMC”
Close the eMMC plugin
Click “Resurrection” and select all options to be repaired, including IMEI and CID
Click “Resurrect”

Please click “Check for updates” button to download and install new updates.

RIFF JTAG - HTC Flyer, Routers, Sat Receivers . . . :)

06.04.2012 RIFF JTAG Updates

Whats new:

RIFF JTAG Manager v1.42
RIFF Box Firmware v1.32

Network Router support:

LinkSys WRT54G Unbrick, Read/Write Flash

Satellite Receivers (STB-s):

Orton 4100C Unbrick, Read/Write Flash
EuroSky ES-4100 Unbrick, Read/Write Flash

HTC Phones support:

HTC Flyer Boot repair, Unlock, CID, ModelID, S-Off, IMEI Update

HTC Phones bug fix and updates:

HTC Sensation (HTC Pyramid) S-Off support added
HTC Evo 3D (HTC Shooter) S-Off support added
HTC Desire HD DBL reflash support added
HTC Desire Z DBL reflash support added

RIFF Torrent Tracker updates:

06.04.2012 HTC_Working_Full_flash_Backups_06.04.2012_v2.torre nt

New HTC Full Backups torrent is uploaded and ready for seeding.

New files for following models: HTC 7 Pro (tested with hspl)
HTC Evo 3D (for Liteon camera)
HTC Desire HD (hboot 2.00 with fix for network problem)
HTC Sensation
HTC Kaiser
HTC Surround
HTC Incredible S

Complete list of files:

06.04.2012 Samsung_Full_flash_backups_06.04.2012_v2.torrent

New files for many new models added.

*** for all sam&htc full flash backups=please contact us ***

RIFF JTAG – Samsung Galaxy Mini – GT-S5570i Unbrick – Boot repair supported

03.04.2012 RIFF JTAG – Samsung Galaxy Mini – GT-S5570i Unbrick – Boot repair supported
Repairing bricked Samsung S5570i is easy with RIFF Box. To power the phone connect USB cable and insert battery. Sometimes it’s needed to press Power On key.
In case phone is not detected de-power phone completely, then wait few seconds, insert USB cable and then insert battery.

To resurrect Samsung S5570i:

Solder JTAG cable to Samsung S5570i JTAG pads;
Connect USB cable to phone and PC;
Insert battery;
Make sure Samsung S5570i is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

Disconnect PC cable;
Insert battery;
Hold both ‘Volume Down’ and ‘Menu’ keys and press Power-On.
If nothing happens, try an alternative: hold both ‘Volume Up’ and ‘Menu’ keys and press Power-On.

RIFF JTAG – Samsung Galaxy Ace – GT-S5830i Unbrick – Boot Repair supported

03.04.2012 RIFF JTAG – Samsung GT-S5830i Unbrick – Boot Repair supported

Repairing bricked Samsung GT-S5830i is easy with RIFF Box. To power the phone connect USB cable and insert battery. Sometimes it’s needed to press Power On key.
In case phone is not detected de-power phone completely, then wait few seconds, insert USB cable and then insert battery.

To resurrect Samsung S5830i:

Solder JTAG cable to Samsung S5830i JTAG pads;
Connect USB cable to phone and PC;
Insert battery;
Make sure Samsung S5830i is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

Disconnect PC cable;
Insert battery;
Hold both ‘Volume Down’ and ‘Menu’ keys and press Power-On.
If nothing happens, try an alternative: hold both ‘Volume Up’ and ‘Menu’ keys and press Power-On.

RIFF JTAG – HTC Inspire 4G A9192 (HTC Stallion) Unbrick, Boot, IMEI, CID, ModelID, Unlock supported

HTC Inspire 4G A9192 (HTC Stallion) Unbrick, Boot, IMEI, CID, ModelID, Unlock supported

Resurrecting HTC Inspire is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Some (or all) revisions of HTC Inspire boards have JTAG interface disabled (that is enable MARM JTAG Fuse is blown in the MSM chip). In this case the JTAG may be enabled only by firmware itself. This is done by the FSBL loader, so writing to FSBL area is artificially disabled in the DCC Loader code. DCC Loader will discard all flashing attempts into FSBL zone and will respond with success code as if flashing succeeded. In this way FSBL zone is protected while user still can flash full image files seamlessly.
Resurrector will reflash radio’s boot zone (except FSBL area) and will re-write PDA’s SPL version 0.85.0024. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PD9812000’.
There is option to reflash BOOT and RECOVERY zones.
Please note, if your phone has the FSBL loader damaged and MCU has JTAG FUSE blown then there is no way to resurrect your phone via JTAG interface.

To resurrect HTC Inspire:

Solder JTAG cable to HTC Inspire JTAG pads;
Insert batter and connect USB Data cable;
Make sure HTC Inspire is selected in the list of models;
If you use only battery, press Power On key;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

Disconnect PC cable;
Insert battery;
Hold ‘Volume Down’ key and press ‘Power ON’ button.

10.01.2012 Samsung GT-i8150 Galaxy W (Samsung Ancora) Unbrick – Boot repair supported

Resurrecting Samsung I8150 is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Please note, MSM8255T is dual core chipset – it has ARM11 and Qualcomm Scorpion cores. During power on sequence only ARM11 core is visible on the JTAG chain. If boots are not completely damaged and it comes up to initializing of the Scorpion core then Scorpion core appears on the JTAG chain too. This will shift ARM11 from TAP0 into TAP1 position on the chain, while current resurrector has the ARM11 core hardcoded at TAP0 position. Thus make sure to establish JTAG connection in the time range while Scorpion core is not visible yet.
To resurrect Samsung I8150:

Solder JTAG cable to Samsung I8150 JTAG pads;
Make sure Samsung I8150 is selected in the list of models;
Insert battery and connect USB Data cable;
If you use only battery, press Power On key;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

Disconnect PC cable;
Insert battery;
Hold ‘Volume Down’ key and press ‘Power ON’ button.

RIFF JTAG – HTC Panache/Glacier/My Touch 4G Unbrick, IMEI, CID, ModelID, Unlock supported

HTC Panache/Glacier/My Touch 4G Unbrick, IMEI, CID, ModelID, Unlock supported

Resurrecting HTC Glacier is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Some (or all) revisions of HTC Glacier boards have JTAG interface disabled (that is enable MARM JTAG Fuse is blown in the MSM7230 chip). In this case the JTAG may be enabled only by firmware itself. This is done by the FSBL loader, so writing to FSBL area is artificially disabled in the DCC Loader code. DCC Loader will discard all flashing attempts into FSBL zone and will respond with success code as if flashing succeeded. In this way FSBL zone is protected while user still can flash full image files seamlessly.
Resurrector will reflash radio’s boot zone (except FSBL area) and will re-write SPL version 0.86.0000. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PD1510000’.
There is option to reflash BOOT and RECOVERY zones.
Please note, if your phone has the FSBL loader damaged and MCU has JTAG FUSE blown then there is no way to resurrect your phone via JTAG interface.

To resurrect HTC Glacier:

Solder JTAG cable to HTC Glacier JTAG pads;
Insert batter and connect USB Data cable;
Make sure HTC Glacier is selected in the list of models;
If you use only battery, press Power On key;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

Disconnect PC cable;
Insert battery;
Hold ‘Volume Down’ key and press ‘Power ON’ button.
_

RIFF JTAG – HTC Inspire 4G A9192 (HTC Stallion) Unbrick, Boot, IMEI, CID, ModelID, Unlock supported

HTC Inspire 4G A9192 (HTC Stallion) Unbrick, Boot, IMEI, CID, ModelID, Unlock supported

To resurrect HTC Inspire:

Solder JTAG cable to HTC Inspire JTAG pads;
Insert batter and connect USB Data cable;
Make sure HTC Inspire is selected in the list of models;
If you use only battery, press Power On key;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

Disconnect PC cable;
Insert battery;
Hold ‘Volume Down’ key and press ‘Power ON’ button.

RIFF JTAG – Samsung GT-i8150 Galaxy W (Samsung Ancora) Unbrick – Boot repair supported

10.01.2012 Samsung GT-i8150 Galaxy W (Samsung Ancora) Unbrick – Boot repair supported

Solder JTAG cable to Samsung I8150 JTAG pads;
Make sure Samsung I8150 is selected in the list of models;
Insert battery and connect USB Data cable;
If you use only battery, press Power On key;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

Disconnect PC cable;
Insert battery;
Hold ‘Volume Down’ key and press ‘Power ON’ button.

RIFF JTAG – Samsung SGH-T759 Exhibit 4G Unbrick – Boot Repair supported

10.01.2012 Samsung SGH-T759 Exhibit 4G Unbrick – Boot Repair supported

Samsung T759 is based on the S5PCxxx Processor (ARM core is Cortex-A8).
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on. But note, in some cases it is possible that you will have to hold Power On key during initial connection.
In case after resurrection (after you have tried with both boot versions) the download mode is not initiated (LCD remains blank) do repeat resurrection with ‘Clone Gremlin zone’ option checked.

To resurrect Samsung T759:

Solder JTAG cable to Samsung T759 JTAG pads;
Connect USB cable to phone and PC;
Attach battery connector;
Make sure Samsung T759 is selected in the list of models;
Make sure a fixed TCK frequency is selected;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

Disconnect PC cable;
Insert battery;
Hold ‘Volume Down’ key and press Power-On.

RIFF JTAG – Samsung Galaxy Fit (GT-S5670) Unbrick – Boot Repair supported

05.01.2012 Samsung Galaxy Fit (GT-S5670) Unbrick – Boot Repair supported

Samsung S5670 resurrection is simple. Make sure to hold Power On button during JTAG connection establishing phase.

To resurrect Samsung S5670 do this:

Solder JTAG cable to Samsung S5670 JTAG pads;
Insert battery and connect USB cable to phone and PC;
Make sure Samsung S5670 is selected in the list of models;
Click Resurrect button;
Press Power On key on the phone;
Wait few seconds until software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

Disconnect PC cable;
Insert battery;
Hold both ‘Volume Down’ and ‘OK’ keys and press Power-On to enter Download Mode;

28.12.2011 Samsung Galaxy Note (GT-N7000) Unbrick – Dead Boot Repair supported

Samsung N7000 AP (PDA Part) is based on the S5PV310 (Exynos 4210) Processor (Cortex-A9 Dual-Core). JTAG pads are very small; professional experience in soldering is required to connect wires to the JTAG interface.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.

To resurrect Samsung N7000 AP:

Solder JTAG cable to Samsung N7000 AP JTAG pads;
Connect USB cable to phone and PC;
Insert battery;
Make sure Samsung N7000 AP is selected in the list of models;
Make sure a fixed TCK frequency is selected;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

Disconnect PC cable;
Insert battery;
Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

27.12.2011 CDMA Olive C2110 Supported

Resurrecting Olive C2110 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x00EC/0×2254

To resurrect Olive C2110:

Solder JTAG cable to Olive C2110 JTAG pads;
Insert USB Data cable into board and PC;
Make sure Olive C2110 is selected in the list of models;
Click Resurrect button;
Choose which areas to flash;
Wait till software signals a successful operation completion;
De-solder JTAG wires;

23.12.2011 CDMA Samsung B339 Breeze Supported

Resurrecting Samsung B339 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x00EC/0×2256

To resurrect Samsung B339:

Solder JTAG cable to Samsung B339 JTAG pads;
Insert USB Data cable into board and PC;
Make sure Samsung B339 is selected in the list of models;
Click Resurrect button;
Choose which areas to flash;
Wait till software signals a successful operation completion;
De-solder JTAG wires;

23.12.2011 CDMA Huawei C3500 Supported

Resurrecting Huawei C3500 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x00EC/0x257E

To resurrect Huawei C3500:

Solder JTAG cable to Huawei C3500 JTAG pads;
Insert USB Data cable into board and PC;
Make sure Huawei C3500 is selected in the list of models;
Click Resurrect button;
Choose which areas to flash;
Wait till software signals a successful operation completion;
De-solder JTAG wires;

22.11.2011 CDMA Huawei C2856 Supported

Resurrecting Huawei C2856 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0×0020/0x88C0

To resurrect Huawei C2856:

Solder JTAG cable to Huawei C2856 JTAG pads;
Insert USB Data cable into board and PC;
Make sure Huawei C2856 is selected in the list of models;
Click Resurrect button;
Choose which areas to flash;
Wait till software signals a successful operation completion;
De-solder JTAG wires;

20.12.2011 CDMA Haier C301R supported

Resurrecting Haier C301R is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x00EC/0x257E

To resurrect Haier C301R:

Solder JTAG cable to Haier C301R JTAG pads;
Insert USB Data cable into board and PC;
Make sure Haier C301R is selected in the list of models;
Click Resurrect button;
Choose which areas to flash;
Wait till software signals a successful operation completion;
De-solder JTAG wires;

19.12.2011 Lenovo LePhone 3G W100 Unbrick – Boot repair supported

Resurrecting Lenovo LePhone 3GW100 is easy. To establish JTAG connection make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
To resurrect Lenovo LePhone 3GW100:

Solder JTAG cable to Lenovo LePhone 3GW100 JTAG pads;
Insert battery;
Make sure Lenovo LePhone 3GW100 is selected in the list of models;
Press and hold Power On key;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

RIFF JTAG - CDMA Updates !

16.12.2011 CDMA Motorola w210 supported

Added support for :- Motorola w210

Please click "Check for Updates" Button in RIFF JTAG Manager to download and install new files.

RIFF Box – JTAG Revolution

RIFF JTAG - Direct JTAG Access to Flash Memory Plugin

16.12.2011 Direct JTAG Access to Flash Memory Plugin v1.00

Details Here:- Memory Plugin v1.00

Bug Fix updates :-

ZTE_AC2746.dll
-------------------------------------
- ID 0x100F80E1 is addedd to allowed list

Samsung_S239.dll
-------------------------------------
- ID 0x100FA0E1 is addedd to allowed list

ZTE_MF180S.dll
-------------------------------------
- ID 0x401200E1 is addedd to allowed list

Samsung_B379.dll
-------------------------------------
- ID 0x220B30E1 is addedd to allowed list

Samsung_M820.dll
-------------------------------------
- ID 0x503E00E1 is addedd to allowed list

Samsung_S5570.dll
-------------------------------------
- ID 0x503C10E1 is addedd to allowed list

RIFF JTAG – Samsung Star Duos (C6712) Unbrick – Boot repair supported

29.11.2011 Samsung Star Duos (C6712) Unbrick – Boot repair supported

Samsung C6712 resurrection is simple. Battery is not required. To power the board it’s most convenient to use an USB Data Cable.
In order to contact to JTAG pads you may need to carefully scratch off paint covering (mask layer) above them. Sometimes there is reset problem with these phones, thus you may need to disconnect and then connect USB cable again.

To resurrect Samsung C6712 do this:

Solder JTAG cable to Samsung C6712 JTAG pads;
Insert battery and connect USB cable to phone and PC;
Make sure Samsung C6712 is selected in the list of models
Click Resurrect button;
Wait few seconds until software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

Disconnect PC cable;
Insert battery;
Hold both ‘Volume Down’ and ‘SIM Swap’ keys and press Power-On.

RIFF JTAG – Samsung Star Duos (C6712) Unbrick – Boot repair supported

29.11.2011 Samsung Star Duos (C6712) Unbrick – Boot repair supported

To resurrect Samsung C6712 do this:

Solder JTAG cable to Samsung C6712 JTAG pads;
Insert battery and connect USB cable to phone and PC;
Make sure Samsung C6712 is selected in the list of models
Click Resurrect button;
Wait few seconds until software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

Disconnect PC cable;
Insert battery;
Hold both ‘Volume Down’ and ‘SIM Swap’ keys and press Power-On.

RIFF JTAG – Unbrick Samsung Galaxy TAB Wi-Fi (P1010), more CDMA Models supported

by admin on Nov.22, 2011, under News

22.11.2011 Unbrick Samsung Galaxy TAB Wi-Fi (P1010), more CDMA Models supported

Samsung P1010 is based on the OMAP3630 (ARM core is Cortex-A8).

Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on. But note, in very rare cases it is possible that you will have to hold Power On key during initial connection.
In case after resurrection (after you have tried with both boot versions) the download mode is not initiated (LCD remains blank) do repeat resurrection with ‘Clone Gremlin zone’ option checked.
Please note, in most cases you will be required to insert Samsung P1010 RIFF™ MagicCard into phone’s SD slot before starting resurrection. In case you don’t have such card yet, you can create it on the “Samsung P1010 RIFF™ MagicCard” page of the resurrector settings dialog.
This is IRAM version of the Samsung P1010 resurrector. We recommend you using it only in case you had problems connecting to phone with normal Samsung P1010 resurrector DLL.

To resurrect Samsung P1010:

Solder JTAG cable to Samsung P1010 JTAG pads;
Insert Samsung P1010 RIFF™ MagicCard into phone’s SD slot;
Connect USB cable to phone and PC;
Insert battery;
Make sure Samsung P1010 is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

Disconnect PC cable;
Insert battery;
Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

There are two DLL-s (Normal and iRAM version) – You can use iRam version in case normal one doesnt work properly. iRam version is much slower, but more robust.

CDMA Models added today :

ZTE AC2766
ZTE AC2746
AnyData ADU555C

RIFF JTAG - SonyEricsson Unlock/IMEI/TA Repair supported

11.11.2011 SonyEricsson Unlock/IMEI/TA Repair supported

Whats new :

With this release, we now support Unlock, IMEI repair and TA repair for listed SE models.
You can now totally rebuild software in these models, after replacing NAND chip for example. At the moment, we have following models released :

x8
x10
x10 mini
x10 mini pro

Remember that these models can have different names (e10, e15, u20 etc)
Please check up this link for more information :

RIFF JTAG – Unlock/IMEI/TA repair – SonyEricsson x8, x10, x10 Mini, x10 mini pro (e15, e10,u20 etc) « RIFF Box – JTAG Revolution

New JTAG Manager has been released too, together with new RIFF Box firmware. Please check this link for more :

RIFF JTAG – JTAG Manager v1.37, RIFF Box firmware v1.28 released « RIFF Box – JTAG Revolution

RIFF Box – JTAG Revolution - Galaxy RulerZZZZZZZZZZZZZZZZZ big grin

RIFF JTAG - Samsung i9003, Samsung m820 supported

28.10.2011 - RIFF JTAG Updates

Whats new :

To download and install updates, please close all running applications and press "Check for Updates" button in RIFF JTAG Manager.

Carefully read resurrection manual for i9003 to avoid frustration ! smile

RIFF Box – JTAG Revolution Galaxy RulerZZZZZZZ

RIFF JTAG - Samsung updates !

19.10.2011 RIFF JTAG – Samsung Z500 supported !

Whats new :

Added support for: Samsung Z500

Please click "Check for Updates" Button in RIFF JTAG Manager to download and install new files.

RIFF Box – JTAG Revolution

RIFF JTAG -Samsung Galaxy II, OMAP4430 version supported (Samsung i9100G, Samsung i9108)

07.10.2011 Samsung Galaxy II, OMAP4430 version supported (Samsung i9100G, Samsung i9108)

Samsung I9108 is based on the OMAP4430 Processor (Cortex-A9 Dual-Core). JTAG pads are very small; professional experience in soldering is required to connect wires to the JTAG interface. There is a big variety of versions of Galaxy II devices: GT-I9100, GT-I9100G, GT-I9100L, GT-I9100M, GT-I9100T, GT-I9101, GT-I9103, GT-I9108, GT-I9188, and maybe more. Some of them are based on different hardware platform – the Samsung S5PV310 (Cortex-A9 Dual-Core). Thus make sure first which exact hardware version you have on hands.

Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.
Current DLL is still a beta one. It will work only with phones which have killed X-Loader.

To resurrect Samsung I9108:

Solder JTAG cable to Samsung I9108 JTAG pads;
Connect USB cable to phone and PC;
Insert battery;
Make sure Samsung I9108 is selected in the list of models;
Make sure a fixed TCK frequency is selected;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

Disconnect PC cable;
Insert battery;
Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

RIFF JTAG – JTAG Manager v1.36, RIFF Box firmware v1.27, GDB Server v1.05 released

07.10.2011 JTAG Manager v1.36, RIFF Box firmware v1.27 released

Whats new :

JTAG Manager 1.36
—————————
- Added fast presets for automatic selection of settings for most common operations on DCC Read/Write page
For this click Settings by Code button and select a desired preset from list and then click Apply Settings.
For example if user selects “Write Full Image into NAND memory” the valid settings on the DCC Read/Write page
for writting full images into devices with NAND memory will be automatically selected
- Fixed serious bug which caused resurrector DLLs which do upload data into RAM to upload broken data
For example DLLs which start Downlad Mode directly use this feature.
- Added feature to accept text name of memory chip from DCC Loader and display it (currently used to display eMMC memory product name)
- Fixed bug for resumming interrupted DCC Read: ifvcurrently cached file size was greater than > 2GB
(that is if read was interrupted on point when there was already more than 2GB of data read) the new reading data was not appended to the readout file end, but instead the file was corrupted.
- Fixed bug for saving big files (after reading on DCC Read/Write page): if size exceeded 0x7FFFFFFF bytes JTAG Manager show no free disk space error.
- Added TEGRA2 chipset selection in the Target list
- Fixed an issue with the resurrection progress bar: in some cases during resurrection operations the progress bar would always stay at 0%.

Firmware 1.27
—————————
- Added TEGRA2 debugging support (dual-core Cortex-A9)
- Added new breakpoint type: “address mismatch” which allows geniune single-stepping on Cortex-A8,A9 (CoreSight) targets
(thus GDB Server can now perform low-level single step commands)

RIFF GDB Server v1.05
—————————–
- Added Thumb2 instructions CBNZ and CBZ for single stepping
- Added more Thumb2 32-bit branch exctructions for single stepping
- Added CoreSight low-level signle-stepping support (at least RIFF BOX Firmware v1.27 is required)

Released updates :

RIFF JTAG – Samsung S7330 Unbrick, Boot repair supported « RIFF Box – JTAG Revolution

RIFF JTAG – CDMA Samsung B209 Breeze Supported « RIFF Box – JTAG Revolution

RIFF JTAG – Samsung Focus (i917) Unbrick, Dead boot repair supported « RIFF Box – JTAG Revolution

RIFF JTAG – Samsung i997 infuse 4g Unbrick, Boot repair supported « RIFF Box – JTAG Revolution

RIFF JTAG -CDMA Samsung F619 supported « RIFF Box – JTAG Revolution

RIFF JTAG – JTAG Manager v1.36, RIFF Box firmware v1.27, GDB Server v1.05 released « RIFF Box – JTAG Revolution

Bug fixes :

Samsung_M110S.dll
-------------------------------------
- pinout picture was corrected

Samsung_I9100.dll
-------------------------------------
- DCC Loader now will report eMCC Card product name

HTC_DesireHD.dll, HTC_DesireS.dll
-------------------------------------
- DCC Loader now will report eMCC Card product name
- Resurrection interface was changed to a more flexible one

Samsung_I917.dll
-------------------------------------
- added resurrection data for phone revisions with 2KB-paged NAND chips

RIFF Box – JTAG Revolution

RIFF JTAG - Samsung and CDMA updates !

03.10.2011 RIFF JTAG - Samsung and CDMA updates !

Whats new :

Added support for Samsung B209

Added support for Samsung S7330 Unbrick

Please click "Check for Updates" Button in RIFF JTAG Manager to download and install new files.

RIFF JTAG – CDMA Samsung B209 Breeze Supported

03.10.2011 CDMA Samsung B209 Breeze Supported

Resurrecting Samsung B209 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x00EC/0×2256

To resurrect Samsung B209:

Solder JTAG cable to Samsung B209 JTAG pads;
Insert USB Data cable into board and PC;
Make sure Samsung B209 is selected in the list of models;
Click Resurrect button;
Choose which areas to flash;
Wait till software signals a successful operation completion;
De-solder JTAG wires;

=========================================================================================================

RIFF JTAG – Samsung S7330 Unbrick, Boot repair supported

by admin on Oct.03, 2011, under News

03.10.2011 Samsung S7330 Unbrick, Boot repair supported

The Samsung S7330 board is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.

To resurrect Samsung S7330:

Solder JTAG cable to Samsung S7330 JTAG pads;
Connect USB cable;
Make sure Samsung S7330 is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

Disconnect PC cable;
Insert battery;
Hold ‘9’ key and press ‘Power ON’ button.
===================================================================================================

30.09.2011 CDMA Sungil SXC1080 Modem supported

Resurrecting Sungil SXC1080 is simple.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x00EC/0x22E0

To resurrect Sungil SXC1080:

Solder JTAG cable to Sungil SXC1080 JTAG pads;
Attach battery or external power supply;
Make sure Sungil SXC1080 is selected in the list of models;
Click Resurrect button;
Choose which areas to flash;
Wait till software signals a successful operation completion;
De-solder JTAG wires;

========================================================================================================

RIFF JTAG – Samsung Anycall m110s Unbrick, Dead boot repair supported

by admin on Sep.30, 2011, under News

30.09.2011 Samsung Anycall m110s Unbrick, Dead boot repair supported

Samsung M110S is based on the S5PCxxx Processor (ARM core is Cortex-A8).
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on. But note, in some cases it is possible that you will have to hold Power On key during initial connection.
In case after resurrection (after you have tried with both boot versions) the download mode is not initiated (LCD remains blank) do repeat resurrection with ‘Clone Gremlin zone’ option checked.

To resurrect Samsung M110S:

Solder JTAG cable to Samsung M110S JTAG pads;
Connect USB cable to phone and PC;
Attach battery connector;
Make sure Samsung M110S is selected in the list of models;
Make sure a fixed TCK frequency is selected;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

Disconnect PC cable;
Insert battery;
Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

=======================================================================================================

RIFF JTAG – CDMA Samsung B209 Breeze Supported

by admin on Oct.03, 2011, under News

03.10.2011 CDMA Samsung B209 Breeze Supported

To resurrect Samsung B209:

Solder JTAG cable to Samsung B209 JTAG pads;
Insert USB Data cable into board and PC;
Make sure Samsung B209 is selected in the list of models;
Click Resurrect button;
Choose which areas to flash;
Wait till software signals a successful operation completion;
De-solder JTAG wires;

(continue reading…)

Leave a Comment :Cdma, Data Cable, Jtag Cable, Memory Chip, Models, Operation Completion, Pc Battery, Presence, Riff, Samsung, Samsung Phone, Samsung Usb more...

RIFF JTAG – Samsung S7330 Unbrick, Boot repair supported

by admin on Oct.03, 2011, under News

03.10.2011 Samsung S7330 Unbrick, Boot repair supported

The Samsung S7330 board is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.

To resurrect Samsung S7330:

Solder JTAG cable to Samsung S7330 JTAG pads;
Connect USB cable;
Make sure Samsung S7330 is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

Disconnect PC cable;
Insert battery;
Hold ‘9’ key and press ‘Power ON’ button.

(continue reading…)

Leave a Comment :Boot Repair, Jtag Cable, Models, Operation Completion, Pc Battery, Pc Cable, Power Supply, Presence, Riff, Samsung, Samsung Usb, Usb Data more...

RIFF JTAG – CDMA Sungil SXC1080 Modem supported

by admin on Sep.30, 2011, under News

30.09.2011 CDMA Sungil SXC1080 Modem supported

Resurrecting Sungil SXC1080 is simple.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x00EC/0x22E0

To resurrect Sungil SXC1080:

Solder JTAG cable to Sungil SXC1080 JTAG pads;
Attach battery or external power supply;
Make sure Sungil SXC1080 is selected in the list of models;
Click Resurrect button;
Choose which areas to flash;
Wait till software signals a successful operation completion;
De-solder JTAG wires;

<<< RIFF BOX-JTAG REVOLUTION >>>

Rocker Team Flashing Interface

we are the authorised Reseller

CONTACT US FOR BEST PRICE

UPDATES

RIFF JTAG - Weekend Updates

18.05.2012 RIFF JTAG – Weekend updates: Whats new:

RIFF JTAG-RIFF JTAG Manager v1.43 released

RIFF JTAG - HTC Flyer, Routers, Sat Receivers . . . :)

28.12.2011 Samsung Galaxy Note (GT-N7000) Unbrick – Dead Boot Repair supported

27.12.2011 CDMA Olive C2110 Supported

23.12.2011 CDMA Samsung B339 Breeze Supported

23.12.2011 CDMA Huawei C3500 Supported

22.11.2011 CDMA Huawei C2856 Supported

20.12.2011 CDMA Haier C301R supported

RIFF JTAG - CDMA Updates !

RIFF JTAG - Direct JTAG Access to Flash Memory Plugin

RIFF JTAG - SonyEricsson Unlock/IMEI/TA Repair supported

RIFF JTAG - Samsung i9003, Samsung m820 supported

RIFF JTAG - Samsung updates !

18.05.2012 RIFF JTAG – Weekend updates:

Whats new: